|
| |
|
| |
|
|
The proposal of the diagram of a pump series
Šály, Peter ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
My diploma thesis describes a procedure of creating interactive computer software for company ISH&MSA Čerpadla a.s. in its theoretical part as well as in its practical part. It is a proposal diagram of centrifugal pumps which consists of made and nonmade pumps. After the selection of a certain pump, according to the required parameters of capacity of pump and transit height, the output of the programme is drawing of a flows characteristic, characteristics of coiled paddlewheel and curves of dissipation without any differences in whether the pump is made or not. There is an operating procedure from the initial work with data, short demonstrations from source code, computation of nonmeasured pump to the ascending flows characteristics in practical part of my diploma thesis. In theoretical part, there are explained principles that are needed for comprehension of a pump reform which are used in practical part.
|
|
|
Maximum attainable efficiencies of one-stage volute pumps
Galuška, Jiří ; Fic, Miloslav (referee) ; Rudolf, Pavel (advisor)
The bachelor’s thesis deals with European Commission Regulation EUROPUMP for minimun allowable efficiency of the one stage volute pumps. Thesis deals with definition, time table and criteria for measurement these pumps. Further thesis deals with total efficiency of the pipe system in relation to pump efficiency. Follow example of a calculation of the one stage volute pump.
|
|
|
Disc friction of centrifugal pumps
Homola, Tomáš ; Klas, Roman (referee) ; Rudolf, Pavel (advisor)
This diploma thesis discusses the issue of the fluid flow instabilities due to rotating discs. It also deals with the calculation of axial force in centrifugal pumps and pressure distribution on cover and support disc of the impeller. Computational simulation of rotating disc is presented with the aim of capturing flow instabilities. Next computational simulation focuses on modelling a gap between the support disc (rotor) and the stator part of the pump for three different geometries, where axial force, pressure distribution on the support disc and loss torque are calculated for each of three models. Obtained results are then compared with the experiment in the conclusion
|
|
|
Disc friction loss in centrifugal pumps and hydraulic turbines
Zemanová, Lucie ; Kozubková, Milada (referee) ; Sedlář, Milan (referee) ; Rudolf, Pavel (advisor)
Dizertační práce je zaměřena na výzkum proudění v mezidiskových spárách hydraulických strojů s důrazem na čerpadla s nízkými specifickými otáčkami. Navzdory tomu, že tekutina v mezidiskových prostorách čerpadel zaujímá velmi malý objem, může výrazně ovlivnit proudění v celém stroji. To má následně vliv na provoz, charakteristiky a celkovou účinnost, zvlášť v případě čerpadel s nízkými specifickými otáčkami, protože stav proudění určuje vznikající diskové ztráty. Rovněž ovlivňuje rozložení tlaku a tím výslednou axiální sílu. Porozumění proudění v mezidiskových spárách je zatím omezené, současné poznatky vychází z teorie odvozené pro značně zjednodušený případ disku rotujícího v hladké válcové spáře. Použitelnost pro popis proudění ve skutečných hydraulických strojích je diskutabilní. Za účelem výzkumu proudění v reálném odstředivém čerpadle bylo navrženo a sestaveno experimentální zařízení umožňující pozorování proudění v zadní mezidiskové spáře pomocí optických metod, měření krouticího momentu a vznikající axiální síly. Také byla popsána metodika pro numerické simulace tohoto druhu proudění umožňující podchytit nestability a vírové struktury. Numerické simulace vhodně doplňují experimentální měření, rozšiřují rozmezí studovaných provozních podmínek a pomáhají popsat jevy, které by šlo měřením jen obtížně odhalit.
|
|
|
Disc friction of centrifugal pumps
Homola, Tomáš ; Klas, Roman (referee) ; Rudolf, Pavel (advisor)
This diploma thesis discusses the issue of the fluid flow instabilities due to rotating discs. It also deals with the calculation of axial force in centrifugal pumps and pressure distribution on cover and support disc of the impeller. Computational simulation of rotating disc is presented with the aim of capturing flow instabilities. Next computational simulation focuses on modelling a gap between the support disc (rotor) and the stator part of the pump for three different geometries, where axial force, pressure distribution on the support disc and loss torque are calculated for each of three models. Obtained results are then compared with the experiment in the conclusion
|
|
|
The proposal of the diagram of a pump series
Šály, Peter ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
My diploma thesis describes a procedure of creating interactive computer software for company ISH&MSA Čerpadla a.s. in its theoretical part as well as in its practical part. It is a proposal diagram of centrifugal pumps which consists of made and nonmade pumps. After the selection of a certain pump, according to the required parameters of capacity of pump and transit height, the output of the programme is drawing of a flows characteristic, characteristics of coiled paddlewheel and curves of dissipation without any differences in whether the pump is made or not. There is an operating procedure from the initial work with data, short demonstrations from source code, computation of nonmeasured pump to the ascending flows characteristics in practical part of my diploma thesis. In theoretical part, there are explained principles that are needed for comprehension of a pump reform which are used in practical part.
|
|
| |
|
| |
guest ::
